automatic import of python-keba-kecontact

3 files changed, 280 insertions, 0 deletions

diff --git a/.gitignore b/.gitignore
index e69de29..ece278d 100644
--- a/.gitignore
+++ b/.gitignore
@@ -0,0 +1 @@
+/keba_kecontact-3.0.3.tar.gz
diff --git a/python-keba-kecontact.spec b/python-keba-kecontact.spec
new file mode 100644
index 0000000..20f88df
--- /dev/null
+++ b/python-keba-kecontact.spec
@@ -0,0 +1,278 @@
+%global _empty_manifest_terminate_build 0
+Name:		python-keba-kecontact
+Version:	3.0.3
+Release:	1
+Summary:	A python library to communicate with the KEBA charging stations via udp
+License:	MIT License
+URL:		https://github.com/dannerph/keba-kecontact
+Source0:	https://mirrors.nju.edu.cn/pypi/web/packages/fc/a4/f0c91103ee3e5bcb79f5ad2f2293dc935790685bd620c88e5219a534a206/keba_kecontact-3.0.3.tar.gz
+BuildArch:	noarch
+
+Requires:	python3-asyncio-dgram
+Requires:	python3-netifaces
+
+%description
+# KEBA KeContact
+
+This is python library to control KEBA charging stations, in specific the P20, P30 and the BMW wallbox.
+Commands were taken from the [UDP Programming Manual](https://www.keba.com/web/downloads/e-mobility/KeContact_P20_P30_UDP_ProgrGuide_en.pdf).
+The library was written for the usage in [Home Assistant](https://www.home-assistant.io/).
+
+## Commands
+The following commands are implemented so far:
+
+### request_data
+
+### set_failsafe
+The failsafe function is a way to detect a failure of the network communication between the UDP application and the charging station.
+In this case, the charging station will fall into a state with a definable current limitation.
+By default, the failsafe function is disabled and must be enabled by the application.
+
+Parameters:
+- timeout in seconds (default = 30 s)
+- fallback_value in ampere (default = 6 A) 
+- persist (default = 0)
+
+### set_energy
+The command setenergy can be used to set an energy limit for an already running or the next charging session.
+If the energy limit is greater than or equal to the value in the E pres field of report 3 the charging session will be stopped and the device will be deactivated (similar to ena 0).
+All settings caused by setenergy are not permanent and are reset at the next time the device registers that the EV plug is pulled from a vehicle inlet or the charging station is restarted.
+
+Parameters:
+- energy in kWh (default = 0 kWh)
+
+### set_current
+This command sets the current limit of the running charging process.
+
+Parameters:
+- current in ampere (default = 0 A)
+
+### set_text
+This command displays a text on the display of the charger.
+
+Parameters:
+- text to show on the display
+- min time to show the text before next text is shown (default = 2 s)
+- max time to show the text (default = 10 s)
+
+### start
+This command authorizes a charging process with the given RFID tag and RFID class.
+
+Parameters:
+- rfid tag as 8 byte hex string, identifier of RFID card
+- rfid class as 10 byte hex string, classifier of RFID card 
+
+### stop
+This command stops a charging process with the given RFID tag.
+
+Parameters:
+- rfid tag as 8 byte hex string, identifier of RFID card
+
+### enable
+The enable command can be used to permanently disable the system by using the parameter 0.
+After receiving ena 0 the device will be disabled until it is rebooted or ena 1 or currtime are used.
+The execution of ena 0 will take approximately 1 second.
+If ena 0 is used, then no other command should be sent for 2 seconds to ensure an undisturbed execution of the disable command.
+
+Parameters:
+- ena in [0,1]
+
+### unlock_socket
+(not tested yet)
+
+
+
+%package -n python3-keba-kecontact
+Summary:	A python library to communicate with the KEBA charging stations via udp
+Provides:	python-keba-kecontact
+BuildRequires:	python3-devel
+BuildRequires:	python3-setuptools
+BuildRequires:	python3-pip
+%description -n python3-keba-kecontact
+# KEBA KeContact
+
+This is python library to control KEBA charging stations, in specific the P20, P30 and the BMW wallbox.
+Commands were taken from the [UDP Programming Manual](https://www.keba.com/web/downloads/e-mobility/KeContact_P20_P30_UDP_ProgrGuide_en.pdf).
+The library was written for the usage in [Home Assistant](https://www.home-assistant.io/).
+
+## Commands
+The following commands are implemented so far:
+
+### request_data
+
+### set_failsafe
+The failsafe function is a way to detect a failure of the network communication between the UDP application and the charging station.
+In this case, the charging station will fall into a state with a definable current limitation.
+By default, the failsafe function is disabled and must be enabled by the application.
+
+Parameters:
+- timeout in seconds (default = 30 s)
+- fallback_value in ampere (default = 6 A) 
+- persist (default = 0)
+
+### set_energy
+The command setenergy can be used to set an energy limit for an already running or the next charging session.
+If the energy limit is greater than or equal to the value in the E pres field of report 3 the charging session will be stopped and the device will be deactivated (similar to ena 0).
+All settings caused by setenergy are not permanent and are reset at the next time the device registers that the EV plug is pulled from a vehicle inlet or the charging station is restarted.
+
+Parameters:
+- energy in kWh (default = 0 kWh)
+
+### set_current
+This command sets the current limit of the running charging process.
+
+Parameters:
+- current in ampere (default = 0 A)
+
+### set_text
+This command displays a text on the display of the charger.
+
+Parameters:
+- text to show on the display
+- min time to show the text before next text is shown (default = 2 s)
+- max time to show the text (default = 10 s)
+
+### start
+This command authorizes a charging process with the given RFID tag and RFID class.
+
+Parameters:
+- rfid tag as 8 byte hex string, identifier of RFID card
+- rfid class as 10 byte hex string, classifier of RFID card 
+
+### stop
+This command stops a charging process with the given RFID tag.
+
+Parameters:
+- rfid tag as 8 byte hex string, identifier of RFID card
+
+### enable
+The enable command can be used to permanently disable the system by using the parameter 0.
+After receiving ena 0 the device will be disabled until it is rebooted or ena 1 or currtime are used.
+The execution of ena 0 will take approximately 1 second.
+If ena 0 is used, then no other command should be sent for 2 seconds to ensure an undisturbed execution of the disable command.
+
+Parameters:
+- ena in [0,1]
+
+### unlock_socket
+(not tested yet)
+
+
+
+%package help
+Summary:	Development documents and examples for keba-kecontact
+Provides:	python3-keba-kecontact-doc
+%description help
+# KEBA KeContact
+
+This is python library to control KEBA charging stations, in specific the P20, P30 and the BMW wallbox.
+Commands were taken from the [UDP Programming Manual](https://www.keba.com/web/downloads/e-mobility/KeContact_P20_P30_UDP_ProgrGuide_en.pdf).
+The library was written for the usage in [Home Assistant](https://www.home-assistant.io/).
+
+## Commands
+The following commands are implemented so far:
+
+### request_data
+
+### set_failsafe
+The failsafe function is a way to detect a failure of the network communication between the UDP application and the charging station.
+In this case, the charging station will fall into a state with a definable current limitation.
+By default, the failsafe function is disabled and must be enabled by the application.
+
+Parameters:
+- timeout in seconds (default = 30 s)
+- fallback_value in ampere (default = 6 A) 
+- persist (default = 0)
+
+### set_energy
+The command setenergy can be used to set an energy limit for an already running or the next charging session.
+If the energy limit is greater than or equal to the value in the E pres field of report 3 the charging session will be stopped and the device will be deactivated (similar to ena 0).
+All settings caused by setenergy are not permanent and are reset at the next time the device registers that the EV plug is pulled from a vehicle inlet or the charging station is restarted.
+
+Parameters:
+- energy in kWh (default = 0 kWh)
+
+### set_current
+This command sets the current limit of the running charging process.
+
+Parameters:
+- current in ampere (default = 0 A)
+
+### set_text
+This command displays a text on the display of the charger.
+
+Parameters:
+- text to show on the display
+- min time to show the text before next text is shown (default = 2 s)
+- max time to show the text (default = 10 s)
+
+### start
+This command authorizes a charging process with the given RFID tag and RFID class.
+
+Parameters:
+- rfid tag as 8 byte hex string, identifier of RFID card
+- rfid class as 10 byte hex string, classifier of RFID card 
+
+### stop
+This command stops a charging process with the given RFID tag.
+
+Parameters:
+- rfid tag as 8 byte hex string, identifier of RFID card
+
+### enable
+The enable command can be used to permanently disable the system by using the parameter 0.
+After receiving ena 0 the device will be disabled until it is rebooted or ena 1 or currtime are used.
+The execution of ena 0 will take approximately 1 second.
+If ena 0 is used, then no other command should be sent for 2 seconds to ensure an undisturbed execution of the disable command.
+
+Parameters:
+- ena in [0,1]
+
+### unlock_socket
+(not tested yet)
+
+
+
+%prep
+%autosetup -n keba-kecontact-3.0.3
+
+%build
+%py3_build
+
+%install
+%py3_install
+install -d -m755 %{buildroot}/%{_pkgdocdir}
+if [ -d doc ]; then cp -arf doc %{buildroot}/%{_pkgdocdir}; fi
+if [ -d docs ]; then cp -arf docs %{buildroot}/%{_pkgdocdir}; fi
+if [ -d example ]; then cp -arf example %{buildroot}/%{_pkgdocdir}; fi
+if [ -d examples ]; then cp -arf examples %{buildroot}/%{_pkgdocdir}; fi
+pushd %{buildroot}
+if [ -d usr/lib ]; then
+	find usr/lib -type f -printf "/%h/%f\n" >> filelist.lst
+fi
+if [ -d usr/lib64 ]; then
+	find usr/lib64 -type f -printf "/%h/%f\n" >> filelist.lst
+fi
+if [ -d usr/bin ]; then
+	find usr/bin -type f -printf "/%h/%f\n" >> filelist.lst
+fi
+if [ -d usr/sbin ]; then
+	find usr/sbin -type f -printf "/%h/%f\n" >> filelist.lst
+fi
+touch doclist.lst
+if [ -d usr/share/man ]; then
+	find usr/share/man -type f -printf "/%h/%f.gz\n" >> doclist.lst
+fi
+popd
+mv %{buildroot}/filelist.lst .
+mv %{buildroot}/doclist.lst .
+
+%files -n python3-keba-kecontact -f filelist.lst
+%dir %{python3_sitelib}/*
+
+%files help -f doclist.lst
+%{_docdir}/*
+
+%changelog
+* Wed May 10 2023 Python_Bot <Python_Bot@openeuler.org> - 3.0.3-1
+- Package Spec generated
diff --git a/sources b/sources
new file mode 100644
index 0000000..dd871af
--- /dev/null
+++ b/sources
@@ -0,0 +1 @@
+26ae88f66ffab221c50ff216004e3376  keba_kecontact-3.0.3.tar.gz